APC SMT2200iC Smart Connect UPS

APC Smart Connect compatible UPS have an inbuilt RJ45 networking port to connect to your network, so they can signal to the APC EcoStruxture cloud. You can then monitor the UPS of all the UPS that you own, and their statuses from one place (APC site). It also can send you and your service partner (you can use our email address if you want us to be your service partner, but it can be any APC provider) when the UPS has a fault, or a life-cycle warning like cell replacement coming up.

Because the UPS we sell are second hand there is a chance that the ID associated with the UPS is registered elsewhere. So far we are finding most of the units are not registered and you can just link to your own account on arrival. APC have realised this will happen, and have a process in place to handle it - if the UPS is registered elsewhere you can contact APC to change the link to your own account.

https://www.smartconnect-support.apc.com/help/EN/index.html#page/EcoStruxure%20Ready%20Smart-UPS%20Help%20Center/MN05.7.17.html

Its best to have an APC account set up (ie a set of credentials that you can use to log into the APC site to move the smartconnect unit onto. 

The case can be started by phone 08002799254
or online http://www.apc.com/uk/en/support/contact/ask_apc.cfm

You should have to hand:

1/ Our invoice (they require proof of purchase),
2/ Photo of your UPS serial number sticker,
3/ Photo of the SmartConnect QR code and ID/Key sticker,
4/ Photo of the UPS LCD panel showing the “about info” including the MAC address,
5/ The eMail address that you use to log into the APC site (works as your account name)

APC will then delete the existing connection and assign it to your email/account name. If you get stuck email us. We toyed with the idea of doing this process for each UPS to register them to ourselves before shipping them out, but given the majority of the SmartConnect UPS so far have been unregistered, its best to leave them unregistered for the simplest set up customer side.

The UPS can be used without setting up smart connect at all.

• Cold-start capable
  Provides temporary battery power when the utility power is out.
• Energy meter
  Provides actual kilowatt hours of usage for energy conscious users.
• Green mode
  Patent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.
• High online efficiency
  Reduces utility costs, generates less heat.
• Intuitive LCD interface
  Provides clear and accurate information in multiple languages with the ability to configure the UPS locally with easy to use navigation keys.
• Predictive replace battery date
  Dynamically provides the month and year when battery replacement is recommended to aide in long term maintenance planning.
• Pure sine wave output on battery
  Simulates utility power to provide the highest degree of compatibility for active PFC (power factor corrected) servers and sensitive electronics.
• Single switched outlet group
  Single outlet group that may be controlled separately from the UPS for discrete reboot of hung devices, sequenced on/off and non-critical load shedding.
• SmartConnect
  Innovative, easy to use remote monitoring feature that provides automatic notifications, firmware updates, and advanced support services.
• SmartSlot
  Customize UPS capabilities with management cards.
• Temperature-compensated battery charging
  Prolongs battery life by regulating the charge voltage according to battery temperature.

Output power capacity 1.98 KWatts / 2.2 kVA
Nominal Output Voltage 230V
Output Voltage Note Configurable for 220 : 230 or 240 nominal output voltage
Output Voltage Distortion Less than 5% at full load
Output Frequency (sync to mains) 47 - 53 Hz for 50 Hz nominal, 57 - 63 Hz for 60 Hz nominal
Topology Line Interactive
Waveform type Sine wave
Output Connections
(8x) IEC 320 C13 (Battery Backup)
(1x) IEC 320 C19 (Battery Backup)

Transfer Time 2ms typical

Nominal Input Voltage 230V
Input frequency 50/60 Hz +/- 3 Hz (auto sensing)
Input Connections IEC-320 C20,
Input voltage range for main operations 160 - 286V
Input voltage adjustable range for mains operation 151 - 302V
Number of Power Cords 1Other Input Voltages 220, 240

Replacement Battery RBC55

Smart Connect network port present.

Interface Port(s) SmartSlot , USBControl panel Multi-function LCD status and control console
Audible Alarm Alarm when on battery : distinctive low battery alarm : configurable delays
Emergency Power Off (EPO) Yes
Available SmartSlot™ Interface Quantity 1

Surge energy rating 365 Joules
Filtering Full time multi-pole noise filtering : 0.3% IEEE surge let-through : zero clamping response time : meets UL 1449

Physical
Maximum Height 435mm , 43.5CM
Maximum Width 197mm , 19.7CM
Maximum Depth 544mm , 54.4CM
Shipping weight 61.9KG