APC SMT750rmi2uC UPS - Smart Connect

APC SMT750RMI2UC rack-mountable 2U UPS with Smart Connect and a short physical depth for your racking system.

Fully tested and working. New cells fitted. 12-month RTB warranty.

This is the revised unit that has the in-built RJ45 data port for the web comms system called "Smart Connect".

You do not need to use the Smart Connect feature. Starting to use the UPS is easy.

1. Unpack and check visually
2. Plug battery connector in
3. Connect mains lead
4. Press on button
5. Attach devices and turn those on.

The UPS is a modern design with a LCD control panel for setup and diagnostics / information. Its a high power density line interactive/pure sine wave type that can be used both in a rack, or as a tower unit.

Specifications

Max Configurable Power (Watts): 500 Watts / 750VA
Output Voltage Note: Configurable for 220 : 230 or 240 nominal output voltage
Output Voltage Distortion: Less than 5 %
Output Frequency (sync to mains): 50/60 Hz +/- 3 Hz Sync to mains
Other Output Voltages: 220 V, 240 V
Topology: Line interactive
Waveform type: Sine wave
Transfer Time: 6 ms typical : 10 ms maximum
Input frequency: 50/60 Hz +/- 3 Hz Auto-sensing
Input voltage range for main operations: 151 - 302 Adjustable, 160 - 286V
Number of Power Cords: 1
Other Input Voltages: 220 V, 240 V
Interface Port(s); RJ-45 Serial, SmartSlot, USB
Control panel: Multifunction LCD status and control console
Audible Alarm: Alarm when on battery : distinctive low battery alarm : configurable delays
Emergency Power Off (EPO): Optional
Available SmartSlot™ Interface Quantity: 1
Maximum Height: 86MM, 8.6CM
Maximum Width: 432MM, 43.2CM
Maximum Depth: 409MM, 40.9CM
Net Weight: 16.6KG

APC Smart Connect compatible UPS have an inbuilt RJ45 networking port to connect to your network, so they can signal to the APC EcoStruxture cloud. You can then monitor the UPS of all the UPS that you own, and their statuses from one place (APC site). It also can send you and your service partner (you can use our email address if you want us to be your service partner, but it can be any APC provider) when the UPS has a fault, or a life-cycle warning like cell replacement coming up.

Because the UPS we sell are second hand there is a chance that the ID associated with the UPS is registered elsewhere. So far we are finding most of the units are not registered and you can just link to your own account on arrival. APC have realised this will happen, and have a process in place to handle it - if the UPS is registered elsewhere you can contact APC to change the link to your own account.

https://www.smartconnect-support.apc.com/help/EN/index.html#page/EcoStruxure%20Ready%20Smart-UPS%20Help%20Center/MN05.7.17.html

Its best to have an APC account set up (ie a set of credentials that you can use to log into the APC site to move the smartconnect unit onto. 

The case can be started by phone 08002799254
or online http://www.apc.com/uk/en/support/contact/ask_apc.cfm

You should have to hand:

1/ Our invoice (they require proof of purchase),
2/ Photo of your UPS serial number sticker,
3/ Photo of the SmartConnect QR code and ID/Key sticker,
4/ Photo of the UPS LCD panel showing the “about info” including the MAC address,
5/ The eMail address that you use to log into the APC site (works as your account name)

APC will then delete the existing connection and assign it to your email/account name. If you get stuck email us. We toyed with the idea of doing this process for each UPS to register them to ourselves before shipping them out, but given the majority of the SmartConnect UPS so far have been unregistered, its best to leave them unregistered for the simplest set up customer side.