SMT2200rmi2uC Smart Connect

utput power capacity 1.98 KWatts / 2.2 kVA 
Nominal Output Voltage 230V 
Output Voltage Note Configurable for 220 : 230 or 240 nominal output voltage 
Output Voltage Distortion Less than 5% at full load 
Output Frequency (sync to mains) 47 - 53 Hz for 50 Hz nominal, 57 - 63 Hz for 60 Hz nominal 
Topology Line Interactive 
Waveform type Sine wave 

Output Connections 
(8x) IEC 320 C13 (Battery Backup) (4x of these are in a switchable group) 
(1x) IEC 320 C19 (Battery backup) 
Transfer Time 4ms typical 8ms max 

Nominal Input Voltage 230V 
Input frequency 50/60 Hz +/- 3 Hz (auto sensing) 
Input Connections IEC-320 C20 
Input voltage range for main operations 160 - 286V 
Input voltage adjustable range for mains operation 151 - 302V 
Other Input Voltages 220, 240 

1x RBC43 
Recharge time 3 hours 

Interface Port(s) RJ-45 Serial , SmartSlot , USB (standard USB-B connector) 
Control panel Multi-function LCD status and control console 
Audible Alarm Alarm when on battery : distinctive low battery alarm : configurable delays 
Emergency Power Off (EPO) Optional 


Surge energy rating 375 Joules 
Filtering Full time multi-pole noise filtering : 0.3% IEEE surge let-through : zero clamping response time : meets UL 1449 

Physical 
Maximum Height 86mm , 8.6CM 
Maximum Width 480mm , 48.0CM 
Maximum Depth 683mm , 68.3CM 
Rack Height 2U 
Net Weight 42.31KG

This is a Smart connect type UPS.

APC Smart Connect compatible UPS have an inbuilt RJ45 networking port to connect to your network, so they can signal to the APC EcoStruxture cloud. You can then monitor the UPS of all the UPS that you own, and their statuses from one place (APC site). It also can send you and your service partner (you can use our email address if you want us to be your service partner, but it can be any APC provider) when the UPS has a fault, or a life-cycle warning like cell replacement coming up.

Because the UPS we sell are second hand there is a chance that the ID associated with the UPS is registered elsewhere. So far we are finding most of the units are not registered and you can just link to your own account on arrival. APC have realised this will happen, and have a process in place to handle it - if the UPS is registered elsewhere you can contact APC to change the link to your own account.

https://www.smartconnect-support.apc.com/help/EN/index.html#page/EcoStruxure%20Ready%20Smart-UPS%20Help%20Center/MN05.7.17.html

Its best to have an APC account set up (ie a set of credentials that you can use to log into the APC site to move the smartconnect unit onto. 

The case can be started by phone 08002799254
or online http://www.apc.com/uk/en/support/contact/ask_apc.cfm

You should have to hand:

1/ Our invoice (they require proof of purchase),
2/ Photo of your UPS serial number sticker,
3/ Photo of the SmartConnect QR code and ID/Key sticker,
4/ Photo of the UPS LCD panel showing the “about info” including the MAC address,
5/ The eMail address that you use to log into the APC site (works as your account name)

APC will then delete the existing connection and assign it to your email/account name. If you get stuck email us. We toyed with the idea of doing this process for each UPS to register them to ourselves before shipping them out, but given the majority of the SmartConnect UPS so far have been unregistered, its best to leave them unregistered for the simplest set up customer side.